免烘烤玻璃油墨
单组份自干玻璃系列油墨【一,油墨使用技术参考】单组份免烤丝网印刷油墨是为是为了不具备烘烤条件而又不用外加固化剂而研制的单组份高性能油墨。油墨使用方便，不需加固化剂，不需烘烤，即可获得优异的附着力。具有平光、附着力佳、耐冲压、耐酒精等特点。1.适用范围:铁、铝、合金、玻璃、陶瓷、电镀、石材、阳极氧化铝表面及烤       （喷）漆面等2.稀释剂:用本公司S-03稀释剂3.固化剂:可添加TA-9154硬化剂10%增加附着力,提高墨膜硬度。4.胶刮硬度: 70-80度为宜，另外角度在60-70度为最佳。5.网目:适合于100-420网目印刷6.用量:用300目网版每公斤约可印30平方米.7.干燥方法: TA系列是属于自然挥发干燥的油墨,墨层表干时间5-10分钟：实干时间在24小时以内. 48小时后达到最佳性能 1．或添加TA-9154硬化剂10%可增加附着力,提高墨膜硬度。2．烤箱90℃烘烤20分钟佳能更优。 【二,测试方法（完全干燥后）】1、划百格后用3M胶纸剥离最少3次以上,无掉墨现象.2、用浸有纯度99%的酒精的棉球，500G力在油墨表面来回擦拭200次无脱色。 【三、油墨使用注意事】 1．试印确认符合要求后再批量生产。 2．做好被印物的表面清除油脂及杂质工作，以促进附着效果。 3．需要套色时，应在前颜色表干或硬干后再进行套色工作。 4．附着力、硬度、耐酸性、耐油性、耐去渍油性、抗划伤性、耐磨性等性能的检测，需要墨层完全固化后方可检测。 5．未经允许情况下，不得将本系列油墨与其它类型油墨混用及配色。 6.添加固化剂后的使用时限：加入固化剂后的油墨使用时间为4~6小时，环境温度越高使用时间越短，剩余油墨不可回收。 【四、油墨使用安全规则】    1、油墨，稀释剂使用及储存时严禁烟火。    2、使用时注意施工场所的通风状况良好。    3、尽量避免皮肤直接接触。    4、本品不慎溅入口、鼻、眼、耳内，应用大量水清洗或直接求助医生。    5、对本品过敏者，使用前应涂覆一层皮肤扶肤膏或戴不渗透性手套。




油墨具有耐酒精，耐汽油，耐磨擦，耐百格，耐植物油，耐化学品等特性

，批量采购有折扣，欢迎大家咨询。

Stem from the glass ink series [a, the use of ink technology reference] one component bake screen printing ink is to do not have the baking condition without external curing agent and the development of one component high performance ink is one component. Ink easy to use, without curing agent, do not need to bake, you can get excellent adhesion. Having a flat, good adhesion, impact resistance, alcohol resistance characteristics. 1. Scope of application: iron, aluminum, alloy, glass, ceramics, electroplating, stone, anodic alumina surface and grilled (spray paint etc.) 2. Thinner: with the company s-03 thinner. Curing agent: can be added ta-9154 hardener 10% increase in adhesion, improve the ink film hardness. 4 glue scratch hardness: 70-80 degree is appropriate, in addition angle of 60-70 degrees for the best. 5. Mesh: for in 100-420 mesh printing. Dosage: 300 mesh screen per kilogram can be printed 30 square meters. Drying methods: TA series is belongs to the natural volatile drying inks, ink layer surface dry time 5-10 minutes: action in time within 24 hours, 48 hours after reach the best performance of 1 or add ta-9154 hardener 10% can increase the adhesion, improve the ink film hardness. 2 oven 20 for 90 minutes, Canon is better. [2, test method for (completely dry)] 1, row grid with 3M tape stripping at least 3 times above, no off phenomenon of ink 0.2, impregnated with a purity of 99% alcohol tampon, 500g force in ink surface wipe back and forth 200 times without decolorization. [three, ink use note] 1 test and confirm the batch production after the request. 2 to do the surface of the printed matter to remove oil and impurities work to promote the attachment effect. 3 need to register, should be before the color table dry or hard after the registration work. 4 adhesion, hardness, acid resistance, oil resistance, stain resistance to oil, scratch resistance, wear resistance and other properties of the detection, the need to completely curing the ink layer can be detected. 5 without permission, may not use the series of ink and other types of ink mixing and matching. 6 after the use of the curing agent: add curing agent after the use of ink for 4~6 hours, the higher the environment temperature, the shorter the use of the remaining ink can not be recycled. [four, ink safety rule] 1, ink, diluent use and storage is prohibited fireworks. 2. Pay attention to the ventilation of the construction site when using.. 3, avoid direct contact with skin. 4, this product accidentally splash entrance, nose, eyes, ears, application of a large number of water wash or direct to the doctor. 5, the allergic person, before using a skin cream or wear impermeable gloves.
The ink has resistance to alcohol, gasoline resistance, abrasion resistance, Naibaige, vegetable oil, chemical resistance and other characteristics
, bulk purchase discounts, welcome to consult