美国vanguard DigiTMR S2断路器特性测试仪
美国vanguard DigiTMR S2  EHV Circuit Breaker Analyzer
The Vanguard DIGITMR S2 is an inexpensive, easy to use digital circuit breaker analyzer. The DIGITMR S2 can be operated stand-alone or can be computer-controlled. It can fully analyze a circuit-breaker’s performance by testing the contact time, stroke, velocity, over-travel, and contact wipe. Contact and motion analysis can be performed for all breaker contact operations (Open, Close, Open – Close, Close – Open, and Open – Close – Open). Timing results are recorded and displayed on the 240 x 128 pixels back-lit LCD screen and can also be printed on the built-in 4.5" wide thermal printer.
Stand-alone, microcomputer-driven EHV Circuit Breaker Analyzer
Analyzes contact time, stroke, velocity, over-travel, and contact wipe
USB PC interface
USB Flash drive interface
Can store up to 200 test records and 100 test plans
Built-in thermal printer
DigiTMR S2
Cables

Cable Part Number
[8000-0005] USB Cable 8000-0005
[8000-0016] Power + Ground Combination Cable 8000-0016
[8000-0095] Contact Extension Cable 8000-0095
[8000-0096] Contact Test Lead 8000-0096
[8000-0097] Contact Extension Cable 8000-0097
[8000-0099] Initiate Cable 8000-0099
[8000-0101] Test Lead (Trigger, V1, V2) 8000-0101
[8000-0104] Transducer Cable 8000-0104
DigiTMR S2
Technical Specifications

TYPE portable digital circuit breaker analyzer
PHYSICAL SPECIFICATIONS 18.5”W x 14”H x 7”D (47.0 cm x 35.7 cm x 17.6 cm);
Weight: 20 lbs (9.1 kg)
INPUT POWER 3 Amps, 100 – 240 Vac, 50/60 Hz
DRY-CONTACT INPUTS 3 dry-contact channels; each channel detects main contact and insertion resistor contact
TIMING WINOOWS 1-second, 10-seconds, or 20-seconds
TIMING RESOLUTIONS ±50 micro-seconds @ 1-second duration, ±500 micro-seconds @ 10-second duration, ±1.00 milli-second @ 20-second duration
TIMING ACCURACY 0.05% of reading ±0.1 ms @ 1-second duration
CONTACT DETECTION RANGE Closed: less than 20 ohms; Open: greater than 5,000 ohm
RESISTOR DETECTION RANGE 50 – 5,000 ohms
TRIGGER INPUT VOLTAGE Open/Close: 30 – 300V, DC or peak AC
VOLTAGE SENSING INPUT RANGE V1: analog input; 0 – 255V, DC or peak AC; Sensitivity: ±1V
V2: voltage presence/absence detector input; 30 – 300V, DC or peak AC
BREAKER OPERATIONS Initiate Open, Close, Open – Close, Close – Open, Open – Close – Open
BREAKER INITIATE CAPACITY 30A, 250 Vac/dc max
INITIATE CURRENT READING RANGE One, non-contact, Hall-effect sensor, 0 – 20 amp range, dc to 5Khz
TRAVEL TRANSDUCER INPUT 1 digital travel transducer channel; Linear range: 0.0 – 60.0 in (±0.005 in.); Rotary range: 0 – 360 degrees (±0.006 degrees)
CONTACT TRAVEL POINT DIFFERENCE Measures “slow-close” contact-point distances; results can be printed
CT CURRENT SENSOR One, non-contact, 0 – 100A
DISPLAY Back-lit LCD screen (240 x 128 pixels); viewable in bright sunlight and low light levels
PRINTER Built-in 4.5-inch wide thermal printer can print both graphic contact travel waveforms and tabulated test results
INTERNAL TEST RECORD STORAGE Stores up to 200 test records and 100 test plans
COMPUTER INTERFACES One USB port, optional Bluetooth interface
PC SOFTWARE WINOOWs-based Vanguard Circuit Breaker Analysis (VCBA S2) software is included with purchase price. Software updates available at no additional charge.
SAFETY Designed to meet UL/IEC 61010 and CAN/CSA C22.2 No. 1010.1-92 standards
ENVIRONMENT Operating: -10°C to 50° C (15°F to +122° F); Storage: -30° C to 70° C (-22°F to +158° F)
OPTIONS Transportation case (available for the DigiTMR S2 and the travel transducers)
WARRANTY One year on parts and labor
Specifications are valid at nominal voltage and ambient temperature of +25C (+77F).


美国vanguard DigiTMR S2 PC PC-controlled EHV Circuit Breaker Analyzer
The Vanguard DIGITMR S2 PC is an inexpensive, easy to use digital circuit breaker analyzer that is designed to be used with a PC. This inexpensive analyzer offers the most cost-effective method for testing circuit breakers. It can fully analyze a circuit-breaker’s performance by testing the contact time, stroke, velocity, over-travel, and contact wipe. Contact-motion analysis can be performed for all breaker contact operations (Open, Close, Open – Close, Close – Open, and Open – Close – Open). The DIGITMR S2 PC offers three dry-contact channels (for timing circuit breaker main and insertion resistor contacts), one digital transducer channel (to monitor CB contact motion), and two voltage monitoring channels.
Inexpensive, PC-controlled EHV circuit breaker analyzer
Optional "on-line" timing mode
Small and light-weight
Can test contact time, stroke, velocity, over-travel, and contact wipe
DigiTMR S2 PC
Cables

Cable Part Number
[8000-0005] USB Cable 8000-0005
[8000-0016] Power + Ground Combination Cable 8000-0016
[8000-0095] Contact Extension Cable 8000-0095
[8000-0096] Contact Test Lead 8000-0096
[8000-0097] Contact Extension Cable 8000-0097
[8000-0099] Initiate Cable 8000-0099
[8000-0101] Test Lead (Trigger, V1, V2) 8000-0101
[8000-0104] Transducer Cable 8000-0104
DigiTMR S2 PC
Technical Specifications

TYPE Portable digital circuit breaker analyzer
PHYSICAL SPECIFICATIONS 18.5”W x 14”H x 7”D (47.0 cm x 35.7 cm x 17.6 cm);
Weight: 16 lbs (7.3 kg)
INPUT POWER 3 Amps, 100 – 240 Vac, 50/60 Hz
DRY-CONTACT INPUTS 3 dry-contact channels; each channel detects main contact and insertion resistor contact
TIMING WINOOWS 1-second, 10-seconds, or 20-seconds
TIMING RESOLUTIONS ±50 micro-seconds @ 1-second duration, ±500 micro-seconds @ 10-second duration, ±1.00 milli-second @ 20-second duration
TIMING ACCURACY 0.05% of reading ±0.1 ms @ 1-second duration
CONTACT DETECTION RANGE Closed: less than 20 ohms; Open: greater than 5,000 ohm
RESISTOR DETECTION RANGE 50 – 5,000 ohms
TRIGGER INPUT VOLTAGE Open/Close: 30 – 300V, DC or peak AC
VOLTAGE SENSING INPUT RANGE V1: analog input; 0 – 255V, DC or peak AC; Sensitivity: ±1V
V2: voltage presence/absence detector input; 30 – 300V, DC or peak AC
BREAKER OPERATIONS Initiate Open, Close, Open – Close, Close – Open, Open – Close – Open
BREAKER INITIATE CAPACITY 30A, 250 Vac/dc max
INITIATE CURRENT READING RANGE One, non-contact, Hall-effect sensor, 0 – 20 amp range, dc to 5Khz
TRAVEL TRANSDUCER INPUT 1 digital travel transducer channel; Linear range: 0.0 – 60.0 in (±0.005 in.); Rotary range: 0 – 360 degrees (±0.006 degrees)
CONTACT TRAVEL POINT DIFFERENCE Measures “slow-close” contact-point distances; results can be printed
CT CURRENT SENSOR One, non-contact, 0 – 100A
COMPUTER INTERFACES One USB port, optional Bluetooth interface
PC SOFTWARE WINOOWs-based Vanguard Circuit Breaker Analysis (VCBA S2) software is included with purchase price. Software updates available at no additional charge.
SAFETY Designed to meet UL/IEC 61010 and CAN/CSA C22.2 No. 1010.1-92 standards
ENVIRONMENT Operating: -10°C to 50° C (15°F to +122° F); Storage: -30° C to 70° C (-22°F to +158° F)
OPTIONS Transportation case (available for the DigiTMR S2 and the travel transducers)
WARRANTY One year on parts and labor
Specifications are valid at nominal voltage and ambient temperature of +25C (+77F).