conventional smoke detector
- 价 格：
面议 /
只
- 供 应 地：广东省深圳市
- 发布公司：深圳市铠卫安全技术有限公司
- 产品型号：YT102
- 品 牌：convoytech
- 发布日期：2013/8/6 15:17:46
- 联系人QQ：707562957
- 文档下载：多线烟感探测器说明书
详细说明
conventional smoke detector
YT102 conventional smoke detector
conventional smoke detector with CE certificate
Operating Voltage Range: 9 to 28VDC Volts Non-polarized
Standby Current: ≤60µA @ 24 VDC
Maximum Alarm Current (LED on: ) ≤30mA @ 24 VDC
Operating Humidity Range: 10% to 93% Relative Humidity, Non-condensing
Operating Temperature Range: 14°F to 122°F (-10°C to50°C)
Adjustable Sensitivity: 1.06±.26%FT.
Height: 2.2? (55 mm) installed in Base
Diameter: 4.0? (103 mm)
Weight: 5.5 oz. (155 g)
BEFORE INSTALLING
NOTICE: This manual should be left with the owner/user of this equipment.
IMPORTANT: The detector must be tested and maintained regularly following NFPA 72 requirements. The detector should be cleaned at least once a year.
GENERAL DESCRJPTION
The device is photoelectronic detector uses a state of-the-art optical sensing chamber. This detector is designed to provide open area protection and to be used with most conventional fire alarm control panel.
Two LEDs on each detector provide local 360° visible alarm indication. They flash every 3~5 seconds indicating that power is applied and the detector is working properly. The LEDs latch on in alarm. LEDs will be off when a trouble condition exists indicating that the detector sensitivity is outside the listed limit. The alarm can be reset only by a momentary power interruption.
INSTALLATION
NOTE: All wiring must conform to applicable local codes, ordinances, and regulations.
NOTE: Verify that all detector bases are installed, that the initiating-device circuits have been tested, and that the wiring is correct.
Remove power from initiating-device circuits before installing detectors.
1. Wire the sensor base per the wiring diagram, Figure 1.
2. Install the sensor into the sensor base. Push the sensor into the base while turning it clockwise to secure it in place.
3. After all sensors have been installed, apply power to the control unit.
4. Test the sensor(s) as described in the TESTING section of this manual.
5. Notify the proper authorities that the system is in operation.
深圳铠卫安全技术有限公司是专门从事消防、安防电子安全产品的研发、生产、贸易为一体的专业化电子公司，产品以外销为主。
公司以：团结、尽责、高效、创新为企业精神，注重企业文化和企业形象,坚持“品质为上”的经营原则,严格控制产品质量，争创行业优秀品牌。
公司生产的全过程，从原材料的采购、进货检验，工序控制，成品检验到产品交付、直至售后服务都严格遵照ISO9002质量保证体系中的有关规定实施控制。设有完善的信息反馈处理网络，对产品的各项指标均按国家或行业标准严格测定。
免责声明：交易有风险，请谨慎交易，以免因此造成自身的损失，本站所展示的信息均由企业自行提供，内容的真实性、准确性和合法性由发布企业负责。本站对此不承担任何保证责任。
898995850
