南京辊筒油加热器，南京反应釜油加热器，南京硫化机油加热器

300度高温油温机/油温机特点
1、最高使用温度300℃
2、微电脑触摸式控制操作简单
3、自动开机排气
4、自动冷却关机
5、出油、回油温度显示
6、模具回水功能（选购）
7、OMRON、FUJI、TE控制零件
8、不锈钢管路，减少管阻及锈垢
9、故障显示，维修不用专业人员

油加热器/油温机安全保护及指示系统：
1、电源欠相保护                    2、总漏电保护开关
3、泵反转保护及指示灯         4、泵过载保护及指示灯
5、过热保护及指示灯             6、模具回水功能（选购）
7、热油BY-PASS洩压回路    8、温度异常警报及指示灯
9、异常警报蜂鸣器                 10、缺油保护及指示灯
300度高温油温机选型方法：
A、求加热器功率或冷冻功率    KW＝W×△t×C×S/ 860×T
    W=模具重量或冷却水  KG
    △t =所需温度和起始温度之间的温差。
   C= 比热   油（0.5），钢（0.11），水（1），塑料（0.45~0.55）
   T=加温至所需温度的时间（小时）

B、求泵的大小 ： 需了解客户所需泵浦流量和压力（扬程）
  P（压力Kg/cm2）=0.1×H（扬程M）×α（传热媒体比重，水=1，油=0.7-0.9）
  L（媒体所需流量L/min）=Q（模具所需热量Kcal/H）/ C（媒体比热水=1  油=0.45）×△t（循环媒体进出模具的温差）×α×60

 

简要介绍：
1、电脑触摸式控制，分离式电气控制，操作简单易懂。（选购）
2、温度控制表采用日本OMRON、RKC微电脑双组P.I.D控制，触措式内储自动演算，精确可靠，省电35%以上。
3、安全保护及故障指示系统完善。
4、采用进口高级组件，日本FUJI、OMROU、法国Schneider、德国SIEMENS、台湾ANLY等。
5、吸出模具回油、全负压运转等功能。（选购）
6、不锈钢一体成型，管捐小，加熟均匀。
7、开机自动排气功能。

300 degrees high temperature oil temperature machine / oil temperature machine

 

1, the highest temperature 300

 

2, microcomputer touch control operation is simple

 

3, automatic starting exhaust

 

4, automatic cooling off

 

5. The temperature of oil and oil return show.

 

6, mold backwater function (optional)

 

7, OMRON, FUJI, TE control parts

 

8, stainless steel piping, reducing pipe resistance and rust scale

 

9, the failure shows that maintenance without professional personnel

 

Oil heater / oil machine safety protection and indicator system:

 

1, power supply is under phase protection 2, total leakage protection switch

 

3, pump reverse protection and indicator 4, pump overload protection and indicator

 

5, overheat protection and indicator 6, mould backwater function (optional)

 

7, BY-PASS oil pressure relief loop 8, abnormal temperature alarm and indicator lamp

 

9, abnormal alarm buzzer 10, lack of oil protection and light

 

300 degrees high temperature oil temperature machine selection method:

 

A, for the heater power or freezing power KW = W * t * C * S/ 860 * T

 

W= die weight or cooling water KG

 

T = the required temperature difference between the temperature and initial temperature.

 

C= specific heat oil (0.5), steel (0.11), water (1), plastic (0.45~0.55)

 

T= temperature to the required temperature of the time (hours)

 

B, the size of the pump: need to understand the pump flow and pressure (lift) customers

 

=0.1 (pressure Kg/cm2) P * H (head M) x alpha (heat transfer media, water =1, oil =0.7-0.9)

 

L (media the required flow L / min) =Q (mold heat Kcal/H) / C (media than hot water = 1 oil = 0.45) x] t (media cycle in and out of the die temperature) and alpha x x 60

 

Brief introduction:

 

1, computer touch control, the separation of electrical control, easy to operate and easy to understand. (optional)

 

2, temperature control table using Japanese OMRON, RKC microcomputer dual group P.I.D control, contact measures within the automatic calculation, accurate and reliable, save more than 35%.

 

3, security and fault indication system perfect.

 

4, the use of imported advanced components, Japan FUJI, OMROU, France Schneider, Germany SIEMENS, Taiwan ANLY, etc..

 

5, import high-quality module, the service life is long. (optional)

 

6, stainless steel integrated molding, tube donation small, add well uniform.

 

7, starting the automatic exhaust function.