供应高强度灌浆料厂家
北京高强无收缩灌浆料厂家韩经理1  北京灌浆料厂家，灌浆料价格，北京高强无收缩灌浆料厂家，北京灌浆料厂家，                                                                                                                                                                                                                                                                                                        高性能水泥基灌浆料      

灌浆料技术特点      
早强、高强        一天强度最高可达50Mpa以上，设备安装完毕一天后即可远行产。      
自流态                现场只需加水搅拌后，直接灌入设备基础，不需震捣便可填充设备基础的全部间隙。      
微膨胀                    以保证设备与基础紧密接触      
耐久性                    200万次疲劳试验，50次冻融循环试验强度无明显变化。      
抗油渗                        在机油中浸泡30天后其强度比浸油前提高10﹪以上。      
灌浆料使用范围      
型号                                                                                                                                                                                                                                            使用范围      
CGM—1〔普通型灌浆料〕      
                    地脚螺栓锚固、裁埋钢筋、灌浆层厚度30mm        基础二次灌浆。      
CGM--2〔普通型灌浆料〕                灌浆层厚度30mm        设备基础二次灌浆。      
CGM—1〔加固型灌浆料〕                灌浆层厚度≥150mm的设备基础二次灌浆。建筑物的梁、板、柱、基础和地坪的补强加固（修补厚度≥40mm）有抗油要求的设备基础二次灌浆。      
CGM--2〔加固型灌浆料〕                灌浆层厚度≥150mm的设备基础二次灌浆。建筑物的梁、板、柱、基础和地坪的补强加固（修补厚度≥40mm）      
CGM--3〔超流态灌浆料〕                高流态、微膨胀，一小时强度可达到20Pma以上。适合于间隙较小的设备基础的二次灌浆，以及对材料流动性要求较高的部位。      
CGM--4〔抢修料〕                超遭抢、微膨胀，一小时强度可达到20Pma以上，适合于铁路枕轨的快速抢修；机场、高速公路等混凝土路面的快速修补；地脚螺栓的快速锚固；建筑物、构筑物的抢修等。      
CGM〔锚固料〕                由无机材料组成，植筋成本低，不含有机挥发物；可在潮湿基面上作业，植筋后面可满足钢筋的焊接要求；与环氧等有机类结构耐久性与混凝土本体一支。      
技术指标      
CGM高性能水泥基灌浆料常规物理性能      
                    抗压强度（Mpa）                竖向膨胀率      
（﹪）                流动度      
（mm）                坍落度      
（mm）                最低施工温度      
（℃）      
                1天                3天                28天                                                                      
CGM--1〔普通型〕                ≥30--50                ≥40—55                ≥65—85                ≥0.02                ≥300                /                --10      
CGM--2〔普通型〕                ≥22--27                ≥38—45                ≥55—65                ≥0.02                ≥270                /                5      
CGM--1〔加固型〕                ≥30--50                ≥40—55                ≥65—85                ≥0.02                /                ≥270                --10      
CGM--2〔加固型〕                ≥22—27                ≥38—45                ≥55—65                ≥0.02                /                ≥270                5      
CGM--3〔超流态〕                ≥20                ≥35                ≥45                ≥0.02                ≥350                /                5      
CGM--4〔抢修料〕                1h≥20                2h≥30                ≥65                ≥0.02                ≥270                /                5      
CGM〔锚固料〕                ≥30                ≥40                ≥65                ≥0.05                /                /                5      
          
钢筋直径（mm）                设计拉力      
（KN）                标准拉力（KN）                极限拉力（KN）                埋设深度≥15D，24小时后的抗垃圾（KN）      
10                24                26                40                ≥40      
12                35                38                58                ≥58      
14                48                52                78                ≥78      
16                62                67                102                ≥102      
18                79                85                130                ≥130      
20                97                105                160                ≥160      
22                118                127                194                ≥194      
25                152                164                250                ≥250      
28                178                206                302                ≥302      
32                233                269                394                ≥394      
36                295                341                499                ≥499      
40                364                421                625                ≥615      
说明：Ⅱ级钢筋胶      
钢筋直径D：10—25f                                                                                                            说明：螺栓锚固及裁埋钢筋的埋设深度应满足设计规范的要求      
推荐埋设深度≥15d        （d：螺栓直径）      
螺旋直径（mm）                螺栓表面与孔壁的距离      
10—14                ≥8      
16—22                ≥15      
24—42                ≥20      
48—64                ≥30      
76—100                ≥40      
＞100                ≥50      


灌浆料                                                灌浆料厂家                                地脚螺栓灌浆料