湖南省湘西灰浆搅拌桶 jb-400型制浆机为我公司自主研发，经多次现场工地使用并不断改进完善后的 定形产品，是浆液配制的专用设备，主要用于水电、铁路、交通、建筑、矿山等 行业的工程施工中，将水泥、膨润土等与水及其添加剂混合并快速制成浆液，该 机采用高速叶轮加涡流制浆，与一般低速叶片搅拌机相比，具有制浆速度快，浆 液搅拌均匀等特点。 2、主要技术参数 公称容量： 400升 许用水灰比： 0.5 ：1 制浆时间(水灰比0.5：1)：3分钟 额定功率： 7.5千瓦 叶轮转速： 1470转/分 重量(包括动力)： 450公斤 外形尺寸(长×宽×高): 1350×1150×1460联系电话：18503915242 李经理

 二次搅拌机技术规格：
1：容量：180-200L-400-600-800-1000L（可选)
2：电机功率：3KW
3：转速：54r/min
4：搅拌量：6m3/h
5：重量：200kg
6：装料高度：980mm
7：外形尺寸：直径*高度：800*1146mm  1000*1200

　产品简介： 　　高浓度搅拌桶：又叫高浓度搅拌槽，可将 水、砂、水泥以及其他高浓度浆 料进行混合搅拌，用电动机三角带传动代动叶轮旋转，将矿浆稀释。 　　高浓度搅拌桶主要特点： 　　1.高浓度搅拌槽是对搅拌槽的螺旋浆式叶轮、循环筒直径、循环筒上的开孔 数及孔径的设计参数进行了改进，使槽内矿浆循环量和搅拌力均有所提高，适合 高浓度介质的搅拌。 　　2.高浓度搅拌槽适用于浓度70%(按质量计)和固体粒度不大于5.0mm的矿浆与 浮选药剂的混合搅拌。 　　3.该机应用于浓度较高矿浆的搅拌,如浓缩后搅拌、砂浆混合搅拌等,搅拌浓 度达75%,有上下两个螺旋相反的叶轮,采用耐纳特橡胶叶片，搅拌叶轮具有耐磨 能力强等特点。湖南省湘西灰浆搅拌桶厂家电话18503915242

---

配合使用泵类产品

湖南省湘西灰浆搅拌桶 高速制浆机是针对低水胶比灌浆材料开发的专用制浆设备，主要用于水电、铁路 、公路、建筑、矿山等行业的工程施工中，将灌浆料或压浆剂、水泥与水混合后 可快速制成浆液。与一般叶片式搅拌机相比，具有制浆效率高、操作简便、浆液 均匀，且具有短距离输送功能等特点 高速制浆机 针对低水胶比灌浆材料开发的专用制浆设备，主要用于水电、铁路、公路、建筑 、矿山等行业的工程施工中，将灌浆料或压浆剂、水泥与水混合后可快速制成浆 液。与一般叶片式搅拌机相比，具有制浆效率高、操作简便、浆液均匀，且具有 短距离输送功能等特点湖南省湘西灰浆搅拌桶 

Safety operation rules for grouting pump operation 1, before the pump preparation and inspection (1) the pump body should be installed firmly on the basis, and check the fastening parts of the power parts. (2) according to the situation, should be as far as possible to shorten the length of suction pipe and suction process, and check the inlet valve, drain valve is good. (3) check the reliability of clutch and gear shift. (4) check the clearance between the piston rod sleeve, connecting rod bearing, crosshead bearing and crosshead slider. (5) check the oil surface of the crankcase oil, check whether there is enough oil in each nozzle, the lubrication of each component is normal. (6) check the reliability of the safety valve, pressure gauge is sensitive, and check the accuracy of the pressure gauge as required. (7) check the entrance to the pulp, no particles larger than 3mm of debris into. (8) rotate the belt pulley by hand for 5 to 6 turns to check whether the pump is flexible. 2, pump operation check (1) put the clutch handle on the off POSTTTION and start the motor. When the operation is normal, close the clutch start pump work, to the LOCAIION of the delivery of slurry. (2) when the pump is working, if it is necessary to change the speed, it is necessary to pull the clutch or stop the pump. (3) always pay attention to the pump drive system has no impact, the impact of sound, the slurry pressure and the amount of slurry is uniform, there is no oil leakage, leakage and other abnormal phenomena. (4) the discharge pressure of the pump shall be controlled within the rated range, observe and control the pressure gauge value at any time, to prevent the exceeding limit of the specified value. (5) in the work should be regularly check the lubrication of the moving parts, each box of lubricating oil temperature in the range of 30 to 50 degrees, the maximum shall not exceed 60 degrees C. (6) the belt in the belt brake can not be stained with oil, so as to prevent the friction plate and the brake valve from slipping. 3, stop pump inspection (1) after opening the three circuit, the clutch is disengaged and the motor is stopped. (2) clean the cylinder head with clean water until clean. (3) during the idle period or in winter, when the pump is stopped, the slurry in the pump and the pipe must be put in the net, and it should be thoroughly cleaned.

 

上一篇 安徽省芜湖市二次双层搅拌机 http://www.b2bzj.com/news/qydt/ll2140478419_49137950.html